| Model | 5L Double Planetary Vacuum Mixer MR-XJB-5L |
| Lower Barrel Parts |
| Design total volume | 8L |
| Elective volume | 2.7-5L |
| Container inner diameter | 240mm |
| Container inside depth | 180mm |
| Container material | The parts in connect with materials is 304 stainless steel |
| Tempering jacket form | The bottom and the barrel jacket can input water for cooling, heat
preservation and heating |
| Tempering jacket port | G3/4",with quick opening movable joint, |
| jacket withstand pressure≤0.4MPa |
| Tempering jacket circulation system | prepared by customer, |
| jacket water inlet temperature≤8℃, |
| cooling water flow＞3.5L/min |
| Discharge materials form | bottom of a G1-1/2" three-piece discharge ball valve, equipped with
2 "standard ISO quick connect clamp connector |
| Design environment temperature | -10～+120°C |
| Move mode | Casters move |
| Mixing Parts |
| Working frequency | 5-50hz |
| Mixing power | 1.5kw |
| Mixing blade speed | 10-98rpm |
| Planetary box rotate speed | 5-50rpm |
| Mixing blade diameter | 124mm |
| Mixing blade model | Variable cross-section spiral twist type, 90 ° helix |
| Mixing blade material | 304 stainless steel |
| Mixing blade line speed | 0.06-0.6m/s |
| Mixing blade number | 2pcs |
| Dispersing Parts |
| Working frequency | 5-50hz |
| Dispersing power | 2.2kw |
| Dispersing rotate speed | 610-6100rpm |
| Dispersing plate diameter | 70mm |
| Dispersing model | Serrated |
| Dispersing plate material | 304 stainless steel |
| Dispersing line speed | 2.2-22m/s |
| Dispersing number | 1pcs |
| Dispersing shaft number | 1pcs |
| Scratch the Wall Parts | Scratch wall bracket material:304 stainless steel |
| Scratch wall material:Teflon |
| Scratch wall rotate speed:Consistent with planetary box rotate
speed |
| Removable or not:Removable design (Need to remove when scraping the
wall on high viscosity process) |
| Base and Lifting Parts | Parts materials:High rigidity structural carbon steel |
| Lifting way:electric |
| Lifting guide:High-precision linear guide |
| Lifting itinerary:≤290mm |
| Upper Barrel Parts | Upper barrel material:304 stainless steel |
| Power feed port:quick opening interface DN40 1pcs |
| Liquid feed port:ISO standard 1/2" quick interface 1pcs |
| Mirror port:DN50 tempered glass sight glass 1pcs |
| Vacuumize port:G1/2 " 1pcs |
| Exhaust port:together with vacuumize port |
| Digital vacuum gauge port:M14×1.5 Internal thread metric tooth
interface 1pcs |
| Control System | Electrical cabinet:Used to install low-voltage electrical
components such as inverter |
| Manual operation panel:For placement buttons, knobs, gauges etc |
| Power supply:AC 3×380V±5﹪,50Hz |
| Control mode:electronic control |
| Power control and speed adjustment mode: Inverter start and control |
| Cooling mode:Air-cooled (wind cooling) |
| Operation mode:Touch screen |
| Digital temperature display gauge:material temperature |
| Emergency stop button:1pcs |
| Alarm system:Over-temperature alarm, over-temperature alarm
shutdown, alarm shutdown |
| Speed display: Touch screen shows the speed |
| Power instructions: 1pcs |
| Safety Chain System | Emergency stop: press the emergency stop switch, the device
immediately stop, and can not do anything |
| Start low-speed mixing: can lift the barrel and turning at the same
time |
| High-speed dispersion: barrel up in place before turning |
| Safe lock in operation: When the machine is running, the mixing
barrel can not be lowered, can not open the mixing barrel. |
| Prevent vacuum tube backflow: special vacuum buffer tank design,
can effectively prevent the vacuum pump oil back to the mixing drum
phenomenon |
| Stop running fault: Inverter comes with overload, overcurrent,
overvoltage, leakage, lack of equal protection |
| Mixing barrel lift: stirring barrel in place to rise |
| Mixing barrel did not return to normal pressure can not be dropped. |
| After mixing barrel rises in place and high-speed dispersion, then
can be started. |
| After mixing barrel rises in place, with locking protection system,
to prevent while the mixing barrel rises to high place abnormal
fall. |
| Dry mixing stage, while the barrel rising, the stirring paddle need
to rotate at the same time. |
| Other description | Temperature probe:Pt100 |
| Temperature measurement: Located of the barrel wall to detection of
internal material temperature |
| Transmission parts bearings:High-speed components for imported
bearings, low-speed components for domestic bearings |
| Oil seal:Domestic brands,O-ring for Static seal,dynamic seal using
mechanical seals or skeleton oil seal |
| Grease:Domestic brands |
| Mechanical seal lubricants:Imported brand |
| Petrol cylinder:Domestic brands |
| Petrol station:Domestic brands |
| Valve:Domestic brands |
| acuum design quantity demand:vacuum system prepared by customer
own, air exhaust volume 2L/S(2X-2) |
| Vacuum hold:-0.098Mpa,holding pressure for 24 hours＞-0.085Mpa,do
not leak to the barrel |
| Total host power:＞4kw |
| Total weight: about 700kg |
| Dimensions:L1463mm×W610mm×H1770mm |
| Appearance color:off-white |
| Ground bearing:900kg/㎡ |
